![Daniel Defense: DDM4 MK18, 5.56mm, SBR, 10.3" Daniel Defense: DDM4 MK18, 5.56mm, SBR, 10.3"](https://cdn11.bigcommerce.com/s-llwpiff/images/stencil/300x300/products/8460/31768/Daniel_Defense_DDM4_MK18_5.56mm_SBR_10.3_right__45046.1714493561.png?c=2)
Daniel Defense: MK18, Mil Spec +, 5.56mm, SBR, 10.3"
The MK18 AR15 style firearm is unmatched in size, weight, and performance, and features the picatinny quad rail Daniel Defense provides to USSOCOM. The RIS II picatinny quad rail features a Bolt-Up System that has been rigorously tested prior to fielding by USSOCOM. The 10.3 inch Cold Hammer Forged barrel is the same length in use for the MK18 upper most commonly used for CQB operations. The independently ambi GRIP-N-RIP Charging Handle accommodates left- and right-handed shooters. This rifle also comes with the ergonomic Daniel Defense Buttstock and Pistol Grip.
MATERIALS & CONSTRUCTION
- LOWER RECEIVER: Mil-Spec with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
- UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
- BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7 Twist, 10.3" Government Profile, Chrome Lined, Mil-Spec Heavy Phosphate Coated, and HP/MPI Tested
- GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 Hardened Steel and Mil-Spec Heavy Phosphate Coating, Carbine Length, Direct Impingement
- MUZZLE DEVICE: Daniel Defense Flash Suppressor, 17-4 PH Stainless Steel, Salt Bath Nitride Finished
- BOLT CARRIER GROUP: M16 Profile, MP Tested, Chrome Lined, Properly Staked Gas Key
- BUFFER: H Buffer
- SIGHTS: Sold Separately
- HANDGUARD: Daniel Defense MK18 RIS II, CNC Machined of 6061-T6 Aluminum, Type III Hard Coat Anodized
- CHARGING HANDLE: GRIP-N-RIP Charging Handle, Body CNC Machined of 7075-T6 Aluminum, Handles & Latch CNC Machined of 6061-T6 Aluminum, Heavy Duty Stainless Steel Roll Pins, Type III Hard Coat Anodized
- RECEIVER EXTENSION: 6 Position Mil-Spec 7075-T6 Aluminum
- BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
- PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
- RAIL LADDERS: 3 low profile ladders made from Santoprene, heat resistant to 300° F.
- Made in the USA!
Specifications
- Mounting System: Picatinny
- Caliber: 5.56mm NATO
- Muzzle Thread : 1 ⁄ 2 × 28 TPI (Threads Per Inch)
- Gas System: Carbine
- Barrel Length: 10.3"
- Barrel Profile: Government
- Product Weight: 5.88 LBS
- Length: 26 3/4"– 29 7/8”
- Magazine: 32 Round - DD Magazine
- Case: Daniel Defense Full-Latch Impact Plastic Case
NFA DISCLAIMER
This firearm is a regulated item by the National Firearms Act (NFA). Please check with your local and state municipalities for any further regulatory requirements. It is the buyer's responsibility to make sure they comply with all NFA rules and applicable laws.
All Daniel Defense products carry a 100% satisfaction guarantee against defects in original materials and workmanship. If your Daniel Defense product shows evidence of such defects, Daniel Defense will make every accommodation to fix, repair, or replace your product in the most expeditious manner possible. Daniel Defense does not warranty products or damage caused to their products by the correct or incorrect installation of other manufacturer's products.
U.S. Government Export Restriction This item is restricted for export by the State Department and Department of Commerce. Make sure that you are familiar with all applicable laws. ITAR Information. |
FFL Requirements & Magazine Restrictions This item has to ship to an FFL. Please read the attached information. Shipping Rules & Magazine Restrictions. |
- PaypalRestrict:
- PaypalRestrict
- Caliber:
- 5.56 NATO
- Length:
- 10.3 inch
- FFL:
- Yes